(Publisher of Peer Reviewed Open Access Journals)
Navigation

International Journal of Advanced Technology and Engineering Exploration (IJATEE)

ISSN (Print):2394-5443    ISSN (Online):2394-7454
Volume-10 Issue-98 January-2023
Full-Text PDF
Paper Title : Performance test of coated HSS tool with respect to thrust force, torque and surface integrity on customized EN8 specimen
Author Name : Roopa D, Vardhaman S Mudakappanavar, R. Suresh and Tataram K Chavan
Abstract :

The scope of this presented work involves the study on effect of cutting speed and feed rate of a customized coated high-speed steel (HSS) tool on thrust force, torque and surface integrity. The standard European norms 8 (EN8) specimen is selected, and its hardness is varied as 15, 20 and 25 Rockwell hardness on the Rockwell C scale (HRC) to make ease of research. Four tools with the composition of R1, R2, R3 and R4 were chosen. Maximum of 67 N thrust force and 8.9 µm surface roughness was obtained at 12.57 m/min cutting speed for 25 HRC specimen. Lower value of thrust force and surface roughness was observed for tool 2. Low as 1.90 µm surface roughness was noticed for 15 HRC specimen when the speed of cut given is 1500 rpm and 1.8µm at a feed rate of 5 mm/rev. A minimum thrust force of 6 and 8 N was observed for feed rate and cutting speed of 5 mm/rev and 62.86 m/min respectively. It was noticed that, thrust force increases gradually when the rate of feed enhanced and is reduced with respect to increase in cutting speed. The tool shows poor performance at the 25 HRC specimen at maximum operating conditions. Tool 2 gives better performance for 15 and 20 HRC of EN8. Thus, tool 2 with R2 composition can be employed till the hardness level of 20 HRC without losing quality of the work.

Keywords : Physical vapour deposition, EN8 (080M40), Thrust force, Torque, Surface integrity.
Cite this article : Roopa D, Mudakappanavar VS, Suresh R, Chavan TK. Performance test of coated HSS tool with respect to thrust force, torque and surface integrity on customized EN8 specimen. International Journal of Advanced Technology and Engineering Exploration. 2023; 10(98):105-118. DOI:10.19101/IJATEE.2021.875381.
References :
[1]https://www.thoughtco.com/history-of-composites-820404. Accessed 13 October 2022.
[2]Chandru M, Selladurai V, Venkatesh C. Experimental evaluation of machinability performance of CNT coated HSS tool during turning of titanium alloy. Journal of Mechanical Science and Technology. 2021; 35(5):2141-50.
[Crossref] [Google Scholar]
[3]Dureja JS, Singh R, Bhatti MS. Optimizing flank wear and surface roughness during hard turning of AISI D3 steel by Taguchi and RSM methods. Production & Manufacturing Research. 2014; 2(1):767-83.
[Crossref] [Google Scholar]
[4]Zhang J, Xue Q, Li SX, Qin Z. Microstructure, corrosion and tribological properties of Ti (CN) multilayer coatings on 35CrMo steel by CVD. Rare Metals. 2020; 39(11):1314-20.
[Crossref] [Google Scholar]
[5]Manoharan M, Kulandaivel A, Arunagiri A, Refaai MR, Yishak S, Buddharsamy G. Statistical modelling to study the implications of coated tools for machining AA 2014 using grey taguchi-based response surface methodology. Advances in Materials Science and Engineering. 2021; 2021:1-20.
[Crossref] [Google Scholar]
[6]Khatai S, Sahoo AK, Kumar R, Panda A. On machining behaviour of various cutting inserts: a review on hardened steel. Materials Today: Proceedings. 2022; 6(6): 3485-92.
[Crossref] [Google Scholar]
[7]Sousa VF, Silva FJ. Recent advances in turning processes using coated tools-a comprehensive review. Metals. 2020; 10(2):1-28.
[Crossref] [Google Scholar]
[8]Dobrzański LA, Lukaszkowicz K, Pakuła D, Mikuła J. Corrosion resistance of multilayer and gradient coatings deposited by PVD and CVD techniques. Archives of Materials Science and Engineering. 2007; 28(1):12-8.
[Google Scholar]
[9]Thirumalai S, Hausberger A, Lackner JM, Waldhauser W, Schwarz T. Anode layer source plasma-assisted hybrid deposition and characterization of diamond-like carbon coatings deposited on flexible substrates. Thin Solid Films. 2018; 655:54-61.
[Crossref] [Google Scholar]
[10]Lessiak M, Haubner R. Diamond coatings on hardmetal substrates with CVD coatings as intermediate layers. Surface and Coatings Technology. 2013; 230:119-23.
[Crossref] [Google Scholar]
[11]Huang B, Zhang EG, Zhou Q, Lin RC, Du HM. Research on the performance of diamond-like carbon coatings on cutting aluminum alloy: cutting experiments and first-principles calculations. Coatings. 2021; 11(1):1-11.
[Crossref] [Google Scholar]
[12]Fernández-abia AI, Barreiro J, Fernández-larrinoa J, De LLL, Fernández-valdivielso A, Pereira OM. Behaviour of PVD coatings in the turning of austenitic stainless steels. Procedia Engineering. 2013; 63:133-41.
[Crossref] [Google Scholar]
[13]Razavykia A, Farahany S, Yusof NM. Evaluation of cutting force and surface roughness in the dry turning of Al–Mg2Si in-situ metal matrix composite inoculated with bismuth using DOE approach. Measurement. 2015; 76:170-82.
[Crossref] [Google Scholar]
[14]Miracle DB. Metal matrix composites–from science to technological significance. Composites Science and Technology. 2005; 65(15-16):2526-40.
[Crossref] [Google Scholar]
[15]Ahmed YS, Alam MS, Arif AF, Veldhuis SC. Use of acoustic emission and cutting force signals to monitor built-up edge formation in stainless steel turning. The International Journal of Advanced Manufacturing Technology. 2019; 103:2257-76.
[Crossref] [Google Scholar]
[16]Suresh R, Basavarajappa S, Gaitonde VN, Samuel GL, Davim JP. State-of-the-art research in machinability of hardened steels. Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture. 2013; 227(2):191-209.
[Crossref] [Google Scholar]
[17]Jacobson M. Surface integrity of hard-turned M50 steel. Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture. 2002; 216(1):47-54.
[Crossref] [Google Scholar]
[18]Claver A, Jiménez-piqué E, Palacio JF, Almandoz E, Fernández DAJ, Fernández I, et al. Comparative study of tribomechanical properties of HiPIMS with positive pulses DLC coatings on different tools steels. Coatings. 2020; 11(1):1-21.
[Crossref] [Google Scholar]
[19]Donnet C, Erdemir A. New horizon in the tribology of diamondlike carbon films. Surface Engineering. 2008; 24(6):399-401.
[Crossref] [Google Scholar]
[20]Varghese V, Akhil K, Ramesh MR, Chakradhar D. Investigation on the performance of AlCrN and AlTiN coated cemented carbide inserts during end milling of maraging steel under dry, wet and cryogenic environments. Journal of Manufacturing Processes. 2019; 43:136-44.
[Crossref] [Google Scholar]
[21]Beake BD, Ning L, Gey C, Veldhuis SC, Kornberg AB, Weaver A, et al. Wear performance of different PVD coatings during hard wet end milling of H13 tool steel. Surface and Coatings Technology. 2015; 279:118-25.
[Crossref] [Google Scholar]
[22]Sahoo AK, Sahoo B. A comparative study on performance of multilayer coated and uncoated carbide inserts when turning AISI D2 steel under dry environment. Measurement. 2013; 46(8):2695-704.
[Crossref] [Google Scholar]
[23]Das A, Kamal M, Das SR, Patel SK, Panda A, Rafighi M, et al. Comparative assessment between AlTiN and AlTiSiN coated carbide tools towards machinability improvement of AISI D6 steel in dry hard turning. Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science. 2022; 236(6):3174-97.
[Crossref] [Google Scholar]
[24]Das SR, Dhupal D, Kumar A. Study of surface roughness and flank wear in hard turning of AISI 4140 steel with coated ceramic inserts. Journal of Mechanical Science and Technology. 2015; 29(10):4329-40.
[Crossref] [Google Scholar]
[25]Chen W, Yan A, Wang C, Deng Y, Chen DC, Xiao H, et al. Microstructures and mechanical properties of AlCrN/TiSiN nanomultilayer coatings consisting of FCC single-phase solid solution. Applied Surface Science. 2020; 509:1-39.
[Crossref] [Google Scholar]
[26]Wan Q, Yang B, Liu HD, Chen J, Zhang J. Microstructure and adhesion of MeN/TiSiN (Me= Ti, Cr, Zr, Mo, NbxAl1− x) multilayered coatings deposited by cathodic arc ion plating. Applied Surface Science. 2019; 497(2019):1-8.
[Crossref] [Google Scholar]
[27]Tillmann W, Stangier D, Meijer A, Krebs E, Ott A, Platt T, et al. Adapting the surface integrity of high-speed steel tools for sheet-bulk metal forming. Journal of Manufacturing and Materials Processing. 2022; 6(2):1-17.
[Crossref] [Google Scholar]
[28]Chandru M, Selladurai V, Venkatesh C. Multiobjective performance investigation of CNT coated HSS tool under the response surface methodology platform. Archives of Metallurgy and Materials. 2021; 66(2): 627-35.
[Crossref] [Google Scholar]
[29]Ikumapayi OM, Afolalu SA, Bodunde OP, Ugwuoke CP, Benjamin HA, Akinlabi ET. Efficacy of heat treatment on the material properties of aluminium alloy matrix composite impregnated with silver nano particle/calcium carbonate Al–AgNp/CaCO3. International Journal of Advanced Technology and Engineering Exploration. 2022; 9(89):523-35.
[Crossref] [Google Scholar]
[30]Rao VD, Ali SR, Ali SM, Geethika VN. Multi-objective optimization of cutting parameters in CNC turning of stainless steel 304 with TiAlN nano coated tool. Materials Today: Proceedings. 2018; 5(12):25789-97.
[Crossref] [Google Scholar]
[31]Sahu AK, Sivarajan S, Padmanabhan R. Optimization of machining parameters in turning of EN31 steel with TiAlN coated cutting tool. Materials Today: Proceedings. 2021; 46:7497-501.
[Crossref] [Google Scholar]
[32]Das A, Das SR, Panda A, Patel SK. Experimental investigation into machinability of hardened AISI D6 steel using newly developed AlTiSiN coated carbide tools under sustainable finish dry hard turning. Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering. 2022; 236(5):1889-905.
[Crossref] [Google Scholar]