Impact of geometries on performances and surface morphology of SLS 3D-printed thrust and roller bearings
Fawzan Hanafi Mohamad Fazdhli1, Muhammad Ilman Hakimi Chua Abdullah1, Ignatius Wong Loke Wei1, Alif Iqmal Abdul Khalid1, Mohd Rizal Alkahari2, Rohana Abdullah1, Mohd Fadzli Abdollah1, Amir Abdullah Muhamad Damanhuri1, Effendi Mohamad1 and Poppy Puspitasari3
Fakulti Teknologi dan Kejuruteraan Mekanikal,Universiti Teknikal Malaysia Melaka, Hang Tuah Jaya, 76100 Durian Tunggal, Melaka,Malaysia1
Centre for Advanced Research on Energy,Universiti Teknikal Malaysia Melaka, Hang Tuah Jaya, 76100 Durian Tunggal, Melaka,Malaysia2
Department of Mechanical and Industrial Engineering,Universitas Negeri Malang,Indonesia3
Centre for Advanced Research on Energy,Universiti Teknikal Malaysia Melaka, Hang Tuah Jaya, 76100 Durian Tunggal, Melaka,Malaysia2
Department of Mechanical and Industrial Engineering,Universitas Negeri Malang,Indonesia3
Corresponding Author : Fawzan Hanafi Mohamad Fazdhli
Recieved : 14-June-2024; Revised : 18-February-2025; Accepted : 21-February-2025
Abstract
Bearings are among the most prevalent elements in civil engineering buildings and mechanical machinery, with numerous applications. The global bearings market has experienced considerable growth in recent years, fuelled by rising demand in the automotive, aerospace, and manufacturing sectors. Bearings were used as early as 40 Before Christ (BC) and commonly have a solid geometrical design. Lately, there have been limited studies to predict the effects of different geometries on the behaviour of bearings. In this study, different geometrical models were designed using CatiaV5 software and manufactured using selective laser sintering (SLS) three-dimensional (3D) printing. The printed geometrical bearing samples were subjected to vibration analysis, performance testing, and surface validation using a scanning electron microscope (SEM) to evaluate their tribological behaviour. The findings indicated that the samples with a triangular geometry exhibited a remarkably smooth surface texture. This smoothness surpassed that of the samples with a square geometry, and this was attributed to the shorter spacing between the melted particles, extensive coverage of the particle area and reduced presence of independent particles. These findings highlight the intricate interplay between geometry and surface texture in bearing fabrication, offering valuable insights for further research and development.
Keywords
Bearings, Geometrical design, Selective laser sintering (SLS), Tribological behaviour, Vibration analysis, Surface texture.
Cite this article
Fazdhli FHM, Abdullah MIHC, Wei IWL, Khalid AIA, Alkahari MR, Abdullah R, Abdollah MF, Damanhuri AAM, Mohamad E, Puspitasari P. Impact of geometries on performances and surface morphology of SLS 3D-printed thrust and roller bearings. International Journal of Advanced Technology and Engineering Exploration. 2025;12(123):186-200. DOI : 10.19101/IJATEE.2024.111101023
References
[1]
Du F, Li D, Sa X, Li C, Yu Y, Li C, et al. Overview of friction and wear performance of sliding bearings. Coatings. 2022; 12(9):1-15.
[2]
Korotkov A, Korotkova L, Vidin D. Study of the quality of plain bearings, used in mining machinery. In E3S web of conferences 2023 (pp. 1-10). EDP Sciences.
[3]
Zhang Z, Gkartzou E, Jestin S, Semitekolos D, Pappas PN, Li X, et al. 3D printing processability of a thermally conductive compound based on carbon nanofiller-modified thermoplastic polyamide 12. Polymers. 2022; 14(3):1-16.
[4]
Lu J. Polymer materials in daily life: classification, applications, and future prospects. In E3S web of conferences 2023 (pp. 1-5). EDP Sciences.
[5]
Rajendran P, Ganesan A. Experimental investigation on friction behavior of selective laser sintering processed parts. 3D Printing and Additive Manufacturing. 2024; 11(3):e1186-95.
[6]
Mehmet I, Dogan G, Chitariu DF, Dumitraș C, Negoescu F. Research on advances in roller bearing manufacturing. In conference series: materials science and engineering 2021 (pp. 1-6). IOP Publishing.
[7]
Sanchez GD, Leventini S, Martini A. Effect of temperature and surface roughness on the tribological behavior of electric motor greases for hybrid bearing materials. Lubricants. 2021; 9(6):1-16.
[8]
Smith TM, Kantzos CA, Zarkevich NA, Harder BJ, Heczko M, Gradl PR, et al. A 3D printable alloy designed for extreme environments. Nature. 2023; 617(7961):513-8.
[9]
Li D, Yang X, Wu Y, Cheng J, Wang S, Wan Z, et al. Theoretical analysis and experimental research of surface texture hydrodynamic lubrication. Chinese Journal of Mechanical Engineering. 2022; 35(1):1-15.
[10]
Kadda M, Nadia B. Elastic behavior of the plain journal bearing coated with a textured surface and a non-textured surface: plain journal bearing at textured surface behavior. International Journal of Surface Engineering and Interdisciplinary Materials Science. 2020; 8(1):55-77.
[11]
Guo Z, Huang Q, Xie X, Yuan C. Effects of spherical-platform texture parameters on the tribological performance of water-lubricated bearings. Wear. 2021; 477:203863.
[12]
Vidyasagar KC, Pandey RK, Kalyanasundaram D. An exploration of frictional and vibrational behaviors of textured deep groove ball bearing in the vicinity of requisite minimum load. Friction. 2021; 9:1749-65.
[13]
Yang Z, Xiong T, Du F, Li B. Topology optimization of stiffener layout design for box type load-bearing component under thermo-mechanical coupling. CMES-Computer Modeling in Engineering & Sciences. 2023; 135(2):1701-18.
[14]
Shan W, Chen Y, Wang X, Yu C, Wu K, Han Z. Nonlinear dynamic characteristics of deep groove ball bearings with an improved contact model. Machines. 2023; 11(3):1-25.
[15]
Zhang P, Wei L, Feng X, Feng F. Friction characteristics of the spiral groove mechanical seal. In journal of physics: conference series 2020 (pp. 1-8). IOP Publishing.
[16]
Liang C, Cai Z, Wu H, Xiao J, Zhang Y, Ma Z. Chloride transport and induced steel corrosion in recycled aggregate concrete: a review. Construction and Building Materials. 2021; 282:122547.
[17]
Chowdhury D, Batham A, Sehgal U, Ghosh C, Bhattacharya B, Datta S. Analysing the frictional properties of micro dimpled surface created by milling machine under lubricated condition. Tribology International. 2020; 146:106260.
[18]
Norani MN, Abdullah MI, Abdollah MF, Amiruddin H, Ramli FR, Tamaldin N. Tribological analysis of a 3D-printed internal triangular flip ABS pin during running-in stage. Jurnal Tribologi. 2020; 27:42-56.
[19]
Gupta N, Tandon N, Pandey RK, Vidyasagar KC, Kalyanasundaram D. Tribological and vibration studies of textured spur gear pairs under fully flooded and starved lubrication conditions. Tribology Transactions. 2020; 63(6):1103-20.
[20]
Esangbedo MO, Abifarin JK. Determination and managerial implications of machine conditions for high-grade industrial polycaprolactam (nylon 6). Scientific Reports. 2023; 13(1):1-8.
[21]
Clavería I, Gimeno S, Miguel I, Mendoza G, Lostalé A, Fernández Á, et al. Tribological performance of nylon composites with nanoadditives for self-lubrication purposes. Polymers. 2020; 12(10):1-22.
[22]
Gadelmoula A, Aldahash SA. Effect of reinforcement with short carbon fibers on the friction and wear resistance of additively manufactured PA12. Polymers. 2023; 15(15):1-14.
[23]
Alo OA, Otunniyi IO, Mauchline D. Correlation of reuse extent with degradation degree of PA 12 powder during laser powder bed fusion and mechanical behavior of sintered parts. Polymer Engineering & Science. 2023; 63(1):126-38.
[24]
Sanders B, Cant E, Kelly CA, Jenkins M. The effect of powder re-use on the coalescence behaviour and isothermal crystallisation kinetics of polyamide 12 within powder bed fusion. Polymers. 2024; 16(5):1-22.
[25]
Lee KP, Kajtaz M. Experimental characterisation and finite element modelling of polyamide-12 fabricated via multi jet fusion. Polymers. 2022; 14(23):1-9.
[26]
Rosso S, Meneghello R, Biasetto L, Grigolato L, Concheri G, Savio G. In-depth comparison of polyamide 12 parts manufactured by multi jet fusion and selective laser sintering. Additive Manufacturing. 2020; 36:1-13.
[27]
Sibisi TH, Shongwe MB, Tshabalala LC, Mathoho I. LAM additive manufacturing: a fundamental review on mechanical properties, common defects, dominant processing variables, and its applications. The International Journal of Advanced Manufacturing Technology. 2023; 128(7):2847-61.
[28]
Enzi A, Mynderse JA. Design and experimental validation of a small-scale prototype selective laser sintering system. SN Applied Sciences. 2019; 1(12):1-10.
[29]
Yan B, Zhang X, Zhu Z. The influence of bearing ring inclination on precision ball bearing contact and heat generation performance. Lubricants. 2022; 10(9):1-14.
[30]
Saldívar MC, Tay E, Isaakidou A, Moosabeiki V, Fratila-apachitei LE, Doubrovski EL, et al. Bioinspired rational design of bi-material 3D printed soft-hard interfaces. Nature Communications. 2023; 14(1):1-11.
[31]
Ngatiman NA, Nuawi MZ, Putra A, Qamber IS, Sutikno T, Jopri MH. Spark plug failure detection using Z-freq and machine learning. TELKOMNIKA (Telecommunication Computing Electronics and Control). 2021; 19(6):2020-9.
[32]
Burda EA, Zusman GV, Kudryavtseva IS, Naumenko AP. An overview of vibration analysis techniques for the fault diagnostics of rolling bearings in machinery. Shock and Vibration. 2022; 2022(1):1-14.
[33]
Brockett C, Carbone S, Jennings L, Fisher J. Influence of material and geometry on the wear of fixed bearing total knee replacements. In Orthopaedic Proceedings 2014 (p. 7). Bone & Joint.
[34]
Morano C, Alfano M, Pagnotta L. Effect of strain rates and heat exposure on polyamide (PA12) processed via selective laser sintering. Materials. 2023; 16(13):1-13.
[35]
Singh J, Singh R, Sharma S. Effect of processing parameters on mechanical properties of FDM filament prepared on single screw extruder. Materials Today: Proceedings. 2022; 50:886-92.
[36]
Schneider J, Kumar S. Multiscale characterization and constitutive parameters identification of polyamide (PA12) processed via selective laser sintering. Polymer Testing. 2020; 86:106357.
[37]
Popova E, Popov VL. The legacy of Coulomb and generalized laws of friction. Proceedings in Applied Mathematics and Mechanics. 2021; 20(1):1-2.
[38]
Khafidh M, Schipper DJ, Masen MA, Vleugels N, Dierkes WK, Noordermeer JW. Validity of Amontons’ law for run-in short-cut aramid fiber reinforced elastomers: the effect of epoxy coated fibers. Friction. 2020; 8:613-25.
[39]
Yu J, Ge J, Yu H, Ye L. Improved bioproduction of the nylon 12 monomer by combining the directed evolution of P450 and enhancing heme synthesis. Molecules. 2023; 28(4):1-19.
[40]
Lates MT, Gavrila CC. Frictional study of the polyamide/rubber contact materials. In conference series: materials science and engineering 2020 (pp. 1-6). IOP Publishing.
[41]
Erinle TJ, Ojaomo KE, Adeoye OS. Fused deposition modelling (FDM) and selective laser sintering (SLS) as indisputable machines in additive manufacturing: a review. Scisynopsis international conference on 3D printing & additive manufacturing. 2023 (pp.1-9).
[42]
Dejene ND, Lemu HG. Current status and challenges of powder bed fusion-based metal additive manufacturing: literature review. Metals. 2023; 13(2):1-22.
[43]
Li M, Xu Y, Fang J. Orthotropic mechanical properties of PLA materials fabricated by fused deposition modeling. Thin-Walled Structures. 2024; 199:1-15.
[44]
Zisopol DG, Tănase M, Portoacă AI. Innovative strategies for technical-economical optimization of FDM production. Polymers. 2023; 15(18):1-22.
[45]
Abdulridha HH, Abbas TF, Bedan AS. Predicting mechanical strength and optimized parameters in FDM-printed polylactic acid parts via artificial neural networks and desirability analysis. Management Systems in Production Engineering. 2024; 32(3):428-37.