(Publisher of Peer Reviewed Open Access Journals)
Navigation

International Journal of Advanced Technology and Engineering Exploration (IJATEE)

ISSN (Print):2394-5443    ISSN (Online):2394-7454
Volume-8 Issue-78 May-2021
Full-Text PDF
Paper Title : Mechanical and metallurgical studies of multi-walled carbon nanotube–reinforced aluminium metal matrix surface composite by friction stir processing
Author Name : R. Raja, Sabitha Jannet and S. Rajesh Ruban
Abstract :

The aluminum alloy 5083 was reinforced with multi-walled carbon nanotubes (MWCNTs) by using friction stir processing (FSP). Different MWCNT volume percentages of 0, 6.06, 12.12, and 18.18% were reinforced into the 5083 aluminium metal matrix. Tensile tests were carried out, and a 24% increase was achieved with 12.12% MWCNTs. Hardness was obtained within the stir zone with the 6.06% of MWCNTs. Scanning Electron Microscopy (SEM) analysis revealed the breakdown of MWCNTs, thus leading to uniform dispersion. Wear rate decreased by 18% with an increase in MWCNTs.
Keywords : Multi-walled carbon nanotubes, SEM, Wear rate, Tensile strength, FSP.
Cite this article : Raja R, Jannet S, Ruban SR. Mechanical and metallurgical studies of multi-walled carbon nanotube–reinforced aluminium metal matrix surface composite by friction stir processing. International Journal of Advanced Technology and Engineering Exploration. 2021; 8(78):643-650. DOI:10.19101/IJATEE.2021.874038.
References :
[1]Lim DK, Shibayanagi T, Gerlich AP. Synthesis of multi-walled CNT reinforced aluminium alloy composite via friction stir processing. Materials Science and Engineering: A. 2009; 507(1-2):194-9.
[Crossref] [Google Scholar]
[2]Jamshidijam M, Akbari-Fakhrabadi A, Masoudpanah SM, Hasani GH, Mangalaraja RV. Wear behavior of multiwalled carbon nanotube/AZ31 composite obtained by friction stir processing. Tribology Transactions. 2013; 56(5):827-32.
[Crossref] [Google Scholar]
[3]Mokdad F, Chen DL, Liu ZY, Xiao BL, Ni DR, Ma ZY. Deformation and strengthening mechanisms of a carbon nanotube reinforced aluminum composite. Carbon. 2016; 104:64-77.
[Crossref] [Google Scholar]
[4]Lu D, Jiang Y, Zhou R. Wear performance of nano-Al2O3 particles and CNTs reinforced magnesium matrix composites by friction stir processing. Wear. 2013; 305(1-2):286-90.
[Crossref] [Google Scholar]
[5]Chen M, Fan G, Tan Z, Xiong D, Guo Q, Su Y, et al. Design of an efficient flake powder metallurgy route to fabricate CNT/6061Al composites. Materials & Design. 2018; 142:288-96
[Crossref] [Google Scholar]
[6]Hosseini SA, Ranjbar K, Dehmolaei R, Amirani AR. Fabrication of Al5083 surface composites reinforced by CNTs and cerium oxide nano particles via friction stir processing. Journal of Alloys and Compounds. 2015; 622:725-33.
[Crossref] [Google Scholar]
[7]Hassanzadeh-Aghdam MK, Ansari R, Mahmoodi MJ. Thermal expanding behavior of carbon nanotube-reinforced metal matrix nanocomposites-a micromechanical modeling. Journal of Alloys and Compounds. 2018; 744:637-50.
[Crossref] [Google Scholar]
[8]Maurya R, Kumar B, Ariharan S, Ramkumar J, Balani K. Effect of carbonaceous reinforcements on the mechanical and tribological properties of friction stir processed Al6061 alloy. Materials & Design. 2016; 98:155-66.
[Crossref] [Google Scholar]
[9]Huang Y, Li J, Wan L, Meng X, Xie Y. Strengthening and toughening mechanisms of CNTs/Mg-6Zn composites via friction stir processing. Materials Science and Engineering: A. 2018; 732:205-11.
[Crossref] [Google Scholar]
[10]Abraham SJ, Madane SC, Dinaharan I, Baruch LJ. Development of quartz particulate reinforced AA6063 aluminum matrix composites via friction stir processing. Journal of Asian Ceramic Societies. 2016; 4(4):381-9.
[Crossref] [Google Scholar]
[11]Khodabakhshi F, Gerlich AP, Švec P. Reactive friction-stir processing of an Al-Mg alloy with introducing multi-walled carbon nano-tubes (MW-CNTs): microstructural characteristics and mechanical properties. Materials Characterization. 2017; 131:359-73.
[Crossref] [Google Scholar]
[12]Mokdad F, Chen DL, Liu ZY, Ni DR, Xiao BL, Ma ZY. Hot deformation and activation energy of a CNT-reinforced aluminum matrix nanocomposite. Materials Science and Engineering: A. 2017; 695:322-31.
[Crossref] [Google Scholar]
[13]Alaneme KK, Sanusi KO. Microstructural characteristics, mechanical and wear behaviour of aluminium matrix hybrid composites reinforced with alumina, rice husk ash and graphite. Engineering Science and Technology, an International Journal. 2015; 18(3):416-22.
[Crossref] [Google Scholar]
[14]Xu H, Hubbard CR, An K, Feng Z, Wang XL, Qu J. Neutron diffraction measurement of residual stresses in friction stir processed nanocomposite surface layer. Advanced Engineering Materials. 2009; 11(8):650-3.
[Crossref] [Google Scholar]
[15]Hu CM, Lai CM, Du XH, Ho NJ, Huang JC. Enhanced tensile plasticity in ultrafine-grained metallic composite fabricated by friction stir process. Scripta Materialia. 2008; 59(11):1163-6.
[Crossref] [Google Scholar]
[16]Sharifitabar M, Sarani A, Khorshahian S, Afarani MS. Fabrication of 5052Al/Al2O3 nanoceramic particle reinforced composite via friction stir processing route. Materials & Design. 2011; 32(8-9):4164-72.
[Crossref] [Google Scholar]
[17]Mazaheri Y, Karimzadeh FA, Enayati MH. Tribological behavior of A356/Al 2 O 3 surface nanocomposite prepared by friction stir processing. Metallurgical and Materials Transactions A. 2014; 45:2250-9.
[Crossref] [Google Scholar]
[18]Yuan Q, Zeng X, Wang Y, Luo L, Ding Y, Li D, Liu Y. Microstructure and mechanical properties of Mg-4.0 Zn alloy reinforced by NiO-coated CNTs. Journal of Materials Science & Technology. 2017; 33(5):452-60.
[Crossref] [Google Scholar]
[19]Sahraeinejad S, Izadi H, Haghshenas M, Gerlich AP. Fabrication of metal matrix composites by friction stir processing with different particles and processing parameters. Materials Science and Engineering: A. 2015; 626:505-13.
[Crossref] [Google Scholar]
[20]Kim WJ, Yu YJ. The effect of the addition of multiwalled carbon nanotubes on the uniform distribution of TiC nanoparticles in aluminum nanocomposites. Scripta Materialia. 2014; 72:25-8.
[Crossref] [Google Scholar]
[21]Bakshi SR, Agarwal A. An analysis of the factors affecting strengthening in carbon nanotube reinforced aluminum composites. Carbon. 2011; 49(2):533-44.
[Crossref] [Google Scholar]
[22]Majid M, Majzoobi GH, Noozad GA, Reihani A, Mortazavi SZ, Gorji MS. Fabrication and mechanical properties of MWCNTs-reinforced aluminum composites by hot extrusion. Rare Metals. 2012; 31:372-8.
[Crossref] [Google Scholar]
[23]Singla D, Amulya K, Murtaza Q. CNT reinforced aluminium matrix composite-a review. Materials Today: Proceedings. 2015; 2(4-5):2886-95.
[Crossref] [Google Scholar]
[24]Tjong SC. Recent progress in the development and properties of novel metal matrix nanocomposites reinforced with carbon nanotubes and graphene nanosheets. Materials Science and Engineering: R: Reports. 2013; 74(10):281-350.
[Crossref] [Google Scholar]
[25]Liu ZY, Xiao BL, Wang WG, Ma ZY. Developing high-performance aluminum matrix composites with directionally aligned carbon nanotubes by combining friction stir processing and subsequent rolling. Carbon. 2013; 62:35-42.
[Crossref] [Google Scholar]
[26]Liu ZY, Xiao BL, Wang WG, Ma ZY. Singly dispersed carbon nanotube/aluminum composites fabricated by powder metallurgy combined with friction stir processing. Carbon. 2012; 50(5):1843-52.
[Crossref] [Google Scholar]
[27]Xie S, Li W, Pan Z, Chang B, Sun L. Mechanical and physical properties on carbon nanotube. Journal of Physics and Chemistry of Solids. 2000; 61(7):1153-8.
[Crossref] [Google Scholar]
[28]Park JG, Keum DH, Lee YH. Strengthening mechanisms in carbon nanotube-reinforced aluminum composites. Carbon. 2015; 95:690-8.
[Crossref] [Google Scholar]
[29]Yoo SJ, Han SH, Kim WJ. Strength and strain hardening of aluminum matrix composites with randomly dispersed nanometer-length fragmented carbon nanotubes. Scripta Materialia. 2013; 68(9):711-4.
[Crossref] [Google Scholar]
[30] Hamdollahzadeh A, Bahrami M, Nikoo MF, Yusefi A, Givi MB, Parvin N. Microstructure evolutions and mechanical properties of nano-sic-fortified aa7075 friction stir weldment: the role of second pass processing. Journal of Manufacturing Processes. 2015; 20:367-73.
[Crossref] [Google Scholar]
[31]Dong S, Zhou J, Hui D, Wang Y, Zhang S. Size dependent strengthening mechanisms in carbon nanotube reinforced metal matrix composites. Composites Part A: Applied Science and Manufacturing. 2015; 68:356-64.
[Crossref] [Google Scholar]
[32]Oden LA, McCune RA. Phase equilibria in the Al-Si-C system. Metallurgical Transactions A. 1987; 18:2005-14.
[Crossref] [Google Scholar]
[33]Goh CS, Wei J, Lee LC, Gupta M. Development of novel carbon nanotube reinforced magnesium nanocomposites using the powder metallurgy technique. Nanotechnology. 2005; 17(1).
[Google Scholar]
[34]Sudhakar M, Rao CS, Saheb KM. Production of surface composites by friction stir processing-a review. Materials Today: Proceedings. 2018; 5(1):929-35.
[Crossref] [Google Scholar]
[35]Xu W, Ke L, Xing L, Zhao X. On the influence of carbon nanotubes on the wear performance and hardness of aluminium matrix composites. Materialwissenschaft und Werkstofftechnik. 2011; 42(5):375-8.
[Crossref] [Google Scholar]
[36]Zhou M, Qu X, Ren L, Fan L, Zhang Y, Guo Y, et al. The effects of carbon nanotubes on the mechanical and wear properties of AZ31 alloy. Materials. 2017; 10(12):1-17.
[Crossref] [Google Scholar]
[37]Zhang XR, Pei XQ, Wang QH, Wang TM, Chen SB. The friction and wear properties of carbon nanotubes/graphite/carbon fabric reinforced phenolic polymer composites. Advanced Composite Materials. 2015; 24(sup1):147-59.
[Crossref] [Google Scholar]
[38]Kumar H, Prasad R, Kumar P, Tewari SP, Singh JK. Mechanical and tribological characterization of industrial wastes reinforced aluminum alloy composites fabricated via friction stir processing. Journal of Alloys and Compounds. 2020.
[Crossref] [Google Scholar]
[39]Patel V, Li W, Liu X, Wen Q, Su Y, Shen J, et al. Tailoring grain refinement through thickness in magnesium alloy via stationary shoulder friction stir processing and copper backing plate. Materials Science and Engineering: A. 2020.
[Crossref] [Google Scholar]
[40]Moharrami A, Razaghian A, Paidar M, Šlapáková M, Ojo OO, Taghiabadi R. Enhancing the mechanical and tribological properties of Mg2Si-rich aluminum alloys by multi-pass friction stir processing. Materials Chemistry and Physics. 2020.
[Crossref] [Google Scholar]
[41]Mazaheri Y, Jalilvand MM, Heidarpour A, Jahani AR. Tribological behavior of AZ31/ZrO2 surface nanocomposites developed by friction stir processing. Tribology International. 2020.
[Crossref] [Google Scholar]
[42]Satyanarayana MV, Kumar A. Influence of cooling media in achieving grain refinement of AA2014 alloy using friction stir processing. Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science. 2020; 234(22):4520-34.
[Crossref] [Google Scholar]
[43]Mabuwa S, Msomi V. The effect of friction stir processing on the friction stir welded AA1050-H14 and AA6082-T6 joints. Materials Today: Proceedings. 2020; 26:193-9.
[Crossref] [Google Scholar]